English Deutsch

Diesel engine Kubota D722 20,9PS 719ccm used

Diesel engine Kubota D722 20,9PS 719ccm used
Product no.: D722

1.895,00 EUR   19 % VAT incl.

Shipping inside Germany: 59,00 EUR *     * Shipping information

Shipping time: 4-5 Days from receipt of payment (except custom-made products)


Diesel engine Kubota D722 20,9PS 719ccm used Item is temporarily not available!

*These are examples.*

Each engine is started dry before shipping !!!

The engines are imported directly from Japan.

Because of the mileage, these engines can be considered as usable.

The engine is filled with oil. A new oil filter is included.

The engine is ready to install!

These are used engines that have been tested and thus controlled (bearings, glow plugs, starters).

The engines were previously completely disassembled and cleaned. Defective parts have been replaced.

There are no new parts installed but according to the motto "two engines make one".

The supplier has been repairing and overhauling diesel engines for 20 years.

The engine is repainted and the oil is filled up. (Please check correct oil level before start-up !!!)

Delivery is without hoses and without thermostat.

After 10 hours of running, please retighten the cylinder head with a torque wrench according to the factory specifications.

.

Specification

The Kubota D722 engine has the same design of crankcase dimensions like the engine D662, ie, the engines are interchangeable.
For comparison, the technical specifications of the D662 model are shown in the table below.

Model D722 comparing D662
   Engine Type    3 cylinder Diesel    3 cylinder Diesel
   capacity    719 ccm   656 ccm
   max.power at 2600 rpm.    20,9 PS / 15,4 kW    19,2 PS / 14,1 kW
   Bore    67 x 68 mm    64 x 68 mm
   Starter system    Electric start 12Volt    Electric start 12Volt
   Weight    63,1 kg    63,7 kg
   Dimensions (WxDxH)    426,2 x 389 x 519,5 mm    426,2 x 389 x 519,5 mm

Following differences on the engines are possible:

Kubota has made minor technical changes depending on the request of the device producer:

short oil pan - long oil pan
Radiator neck right or left
with hydraulic pump - without Hydraulic Pump
Exhaust manifold connection horizontally or vertically

Never changed is the crankcase or the connection points / threaded bore, etc.







A new V-belt is installed.

New oil filter is installed and oil is replenished.

Each engine is test-running about 10 minutes in our workshop before shipping.

Additional accessories:  Price is only valid in conjunction with the engine compartment!

  • Manifold for 30,00 Euro


  • Hydraulic pump for 30,00 Euro


Our warehouse:





(1) Engine type and (2) Engine serial number

Dimensions:



Specification:



performance curves:

Especially this offer as well as the sale are directed exclusively to companies in the sense of the §14 BGB, with your purchase you confirm to be an entrepreneur in the sense of the §14BGB.

The engine is sold as a part carrier without warranty and guarantee. The engine is started dry in our workshop.

A concession on our part to our customers:

For the sake of fairness, we grant you a right of return.

If it becomes apparent before or during use that the engine is unsuitable, we will take back the engine for the purchase price.

The return costs and incidental costs as well as installation and removal expenses are borne by the buyer.

This individual contractual regulation recognizes the customer with his purchase - as we recognize the right of return as well.

The engine production of this type was discontinued before about 1990 and thus this engine is considered "vintage car".

Each Japanese engine manufacturer configures the engine to the specifications of the equipment manufacturer. (Excavator manufacturer, farm loader producer, generator manufacturer, etc.)

For example:

  • Komatsu (excavator) wants the cooling water connection on the right
  • Weidemann wants the cooling water connection on the left and a large flywheel
  • Kubota Japan does not need a thermostat and a temperature transmitter for its tractors
  • For the Asian market, no water pump is needed
  • Exhaust Manifold - upwards - to the front - to the rear
  • Intake manifold - upwards - to the side
  • Oil pan long / oil pan short


For example, if the device series has expired, the device manufacturer orders a further 1000 replacement motors of the same configuration and stores them in stock. If these are sold as replacement engines, these engines are no longer produced in this configuration. Just like any engine, the crankcase is the flange port, engine mount, etc.

Practice Note:

Most of the old engine, the special attachments are attached to "our" engine.

For questions we are happy to help.

Video for the test run:

 

Each engine runs 1/2 h of trial.

- Start with half throttle from 00:04 min

- From 00:27 min he runs on 3/4 gas

- then visual inspection and inspection

SUPPLIERS DECLARATION for components

We hereby declare that the product is designed for mounting in or on a machine.

The machine in which the above-mentioned part is to be installed, should not be put into operation until it was found that the machine complies with the requirements of the Machinery Directive.

Any damage arising therefrom is not chargeable by Motorgeräte Fritzsch GmbH. Motorgeräte Fritzsch GmbH disclaims any liability for damages, because we have no influence on installation, use and safety of the machine.

For Diesel Engines: As none of the major manufacturers give warranty / statutory warranty rights in the use of vegetable oil for diesel engines, we hereby join in this scheme.

 


⇒ Typing errors, misapprehensions and changes excepted.


top top

This product is compatible with:

Starter for Kubota 3 cylinder engines D-series

Starter for Kubota 3 cylinder engines D-series

230,00 EUR (19 % VAT incl. * Shipping information)

Parse Time: 0.281s