HB24S with side shift suitable for small tractors
This is a very solid Backhoe - the material has not been saved. These excavators we sell since 2008.
The backhoe for tractors may be assembled to each tractor. Excavator with side shift, three-point excavators are for private and professional use.
Important!!! Each of our rear dredges has a three-point stiffener (standard)!
The rear dredger is thus firmly connected to the tractor.
This means that lifting and lowering with the rear three-point lifting is no longer possible.
Due to the dead weight of the rear dredger and with the wide reach to the rear, damage to the hydraulics would occur ( bent sub-brakes of broken-out upper steering brackets, etc.).
The three-point stiffening makes the excavator and the tractor a compact unit.
Thus, vibrations, wobbling, and distortions are excluded.
The excavator is stable on its hydraulically extentable supports.
The backhoe is designed for the rear three-point hitch and KATI KATII.
Specifications
- Shovel / bucket length: 60 cm
- Shovel width/Panel width: 30 cm
- Shovel arm Total length: 290 cm
- Sideshift 1,20m
- Drive of the digger is via the tractor PTO
- Dimensions in transport position (HxWxL): 1700 x 1000 x 1400 mm
- max. Working depth: 195 cm
- max. Working radius: 280cm
- max. Lifting height: 317 cm
- Rotation angle: 180 °
- Bucket angle: 203 ° opening angle
- Bucket capacity: 0.017 m3
- Shovel power: 1700 kg
- Weight: 670 kg
- Pump capacity: 40 liters per minute
- Clear dimension of the metal transport box LxWxH 160 x 110 x 230 cm
ATTENTION!
Please shorten the PTO shaft to required length.
Important Note!!! There must be no play between the bolt and the holder.
Due to the absolutely stable processing we offer lifetime warranty against bending of the excavator arms. In case of damage we will send free the relevant arm.
External dimension stabilizer foot to foot support 1,37m
External dimension framework 1,31m
The excavator arm can be hydraulically side-shifted 1,20m.
Side shift is good if you need to dredging a trench right next to a house wall.
The drive of the digger is via the PTO shaft of the tractor. This rear actor has an internal oil circuit with oil tank and PTO pump.
The PTO pump is driven by the supplied PTO shaft.
The oil in the storage tank is not filled because such large amounts of oil are not allowed to remain in the machine during transport, for environmental reasons.
Depending on the backhoe type you have to refill about 25 liters standard hydraulic oil 46S.
The PTO pump is connected directly to the tractor.
The drive tractor should have a minimum weight of 1000 kg, because the rear actor is already 560 kg heavy itself. Otherwise, the weight ratio is wrong.
A: 290cm B: 195cm C: 317cm
The following buckets/shovels are available:
Three buckets are optionally available for the backhoe HB24S. These have the same shape and differ only in the width and the number of digger teeth.
1. basic form
This is the standard bucket with 3 tines.
This is fitted as standard on the excavator.
Image 1: 2 Grave tines - 230 Euro
Image 2: 3 Grave tines - 299 Euro
Image 3: 4 Grave tines - 350 Euro
Standard bucket - standard delivery included
Image 4: 5 Grave tines - 400 Euro
Image 5: Grave spoon - 450 Euro
Image 6: Grave spoon - 400 Euro
| Image |
Number of tines |
Scraping width |
shovel volume |
| 1 |
2 |
26 cm |
0 ,014 m3 |
| 2 |
3 |
30 cm |
0,017 m3 |
| 3 |
4 |
40 cm |
0,022 m3 |
| 4 |
5 |
50cm |
0,028 m3 |
| 5 |
without |
90 cm |
0,061 m3 |
| 6 |
without |
70 cm |
0,045 m3 |
We guarantee a serious carrying out. You have a full right of return.
We also offer a complete retrofit kit - a wooden gripper / loading tongs for attaching to the rear dredger - an inexpensive alternative !!!
