Rear digger, Backhoe HB25S with side shift suitable for small tractors
This is a very solid Backhoe - the material has not been saved. These excavators we sell since 2008.
The backhoe for tractors may be assembled to each tractor. Excavator with side shift, three-point excavators are for private and professional use.
Important!!!
Each of our rear dreders has a three-point stiffener (standard)!
The rear dredger is thus firmly connected to the tractor.
This means that lifting and lowering with the rear three-point lifting is nos longer possible.
Due to the dead weight of the rear dredgerand with the wide reach to the rear, damage to the hydraulics would occur ( bent sub-brakes of broken-out upper steering breckets, etc.).
The three-point stiffening makes the excavator and the tractor a compact unit.
Thus, vibrations, wobbling, and distortions are excluded.
The excavator is stable on its hydraulically exendable supports.
The backhoe is designed for the rear three-point hitch and KATI KATII.
Specifications
- Shovel / bucket length: 60 cm
- Shovel width/panel width: 40 cm
- Shovel arm Total length: 330 cm
- Sideshift 1,37m
- Drive of the digger is via the tractor PTO
- Dimensions in transport position (LxWxH): 1400 x 1000 x 1900 mm
- max. Working depth: 225 cm
- max. Working radius: 280cm
- max. Lifting height: 345 cm
- Rotation angle: 180 °
- Bucket angle: 203 ° opening angle
- Bucket capacity: 0.028 m3
- Bucket power: 1700 kg
- Weight: 860 kg
- Pump capacity: 40 liters per minute
- Hydraulic pressure 160 bar
- Clear dimension of the metal transport box LxWxH 160 x 110 x 230 cm
ATTENTION!
Please shorten the PTO shaft to required length.
We guarantee a serious carrying out. You have a full right of return.
Important Note!!! There must be no play between the bolt and the holder.
Due to the absolutely stable processing we offer lifetime warranty against bending of the excavator arms. In case of damage we will send free the relevant arm.
External dimension stabilizer foot to foot support 1,55m
External dimension framework 1,45m
The excavator arm can be hydraulically side-shifted 1,37m.
Side shift is good if you need to dredging a trench right next to a house wall.
The drive of the digger is via the PTO shaft of the tractor. This rear actor has an internal oil circuit with oil tank and PTO pump.
The PTO pump is driven by the supplied PTO shaft.
The oil in the storage tank is not filled because such large amounts of oil are not allowed to remain in the machine during transport, for environmental reasons.
Depending on the backhoe type you have to refill about 25 liters standard hydraulic oil 46S.
The 4-pronged blade (40 cm wide) is included.
The PTO pump is connected directly to the tractor.
Sorry, the PTO protection, we have omitted it for clarity in photographs - but it is standard included.
The drive tractor should have a minimum weight of 1000 kg, because the rear actor is already 860 kg heavy itself. Otherwise, the weight ratio is wrong.
The excavator is pivotable 180 °.
A: 330cm B: 225cm C: 345cm
The following buckets/shovels are available:
Three buckets are optionally available for the backhoe HB25S. These have the same shape and differ only in the width and the number of digger teeth.
1. basic form
This is the standard bucket.
This is fitted as standard on the excavator.
2. optional types
Image 1: 2 teeth digger - 230 Euro
Image 2: 3 teeth digger - 299 EUR
Image 3: 4 teeth digger - 350 EUR
Standard bucket - standard included
Bild 4: 5 teeth digger- 400 Euro
Image 5: digger shovel - 450 EUR
Image 6: digger shovel - 400 EUR
| Image |
Number of teeth |
panel width B |
bucket capacity |
| 1 |
2 |
26 cm |
0,014 m3 |
| 2 |
3 |
30 cm |
0,017 m3 |
| 3 |
4 |
40 cm |
0,022 m3 |
| 4 |
5 |
50 cm |
0,028 m3 |
| 5 |
without |
90 cm
|
0,061 m3 |
| 5 |
without |
70 cm |
0,045 m3 |
We also offer a complete retrofit kit - a timber grab / Log gripper for attachment to the backhoe - an inexpensive alternative!
