English Deutsch

round baler press 850Z hay baler straw press for compact tractors

round baler press 850Z hay baler straw press for compact tractors
Product no.: 850Z

4.850,00 EUR   19 % VAT incl.

Shipping inside Germany: 120,00 EUR *     * Shipping information

Shipping time: immediately available from stock, since we have several stores in the vicinity, we ask for tel. Pre-registration for pick-up

2 years warranty + 1 year MGF parts warranty!

round baler press 850Z hay baler straw press for compact tractors

This baler can be connected to tractors - PTO drive. It is attached to the rear three-point linkage of the tractor.

Thus, the windrow is below the tractor.

The bales have a diameter of about 50cm and a length of about 70cm.

The hay bales is not wrapped in a mesh but with a rope.

The baler has no central lubrication, therefore it must be lubricated separately.

The PTO is included!

It is characterized by simple technology.

It has been specifically designed for use in mountainous terrain. With its low center of gravity tipping is almost impossible.

Because of the small outside dimensions, it is ideal for small areas where the large technique can not be used.

About every 40 seconds the machine produces a hay bale that weighs 22 kg.

The formation of (mini) hay bales of any kind is known as soft-hearted, because the ball heart is less pressed to allow the hay a correct transpiration and to prevent a possible mold growth.

The outside is much denser pressed to produce a water-repellent self sparing hay layer around the round bale.

Bale density can be adjusted in 3 steps.

Pressing is done without cutting and threshing, to preserve the original quality of the hay.

Due to its handy size the hay bales are ideal for horse owners and horse farms, etc

Technische Daten

  • Suitable for tractors from 13,0PS
  • Power Requirements: 6,6 - 14,8 kW
  • Ball Dimensions: 70 x 50 cm
  • Weight of hay bales produced: 20-25 kg
      Straw bales 14-18 kg
      Silage bales 30-50 kg
  • Hour production / Capacity: 50-80 pcs
  • collecting width: 800 mm
  • Tines of the pickup intake: 6 tines with 12 double tines
  • Tying with rope: standard
  • Signal for bale formation: standard
  • Total weight with operating equipment: 402 kg
  • Tires: 16x6.50-8
  • min. Working speed of the machine: 2,5 km/h

The baler is tested and set in the manufacturer's factory! The wheel set is not mounted. The bale press was then packed into a transport iron rack 1.15 x 1.15 m x 1.20 m.

Sample video:


The baler is lowered. The blade holder is lowered and is set with the chain to working height, turn on and start PTO. The electric cable is connected to the battery. If the bales pressed it honks automatically.

Then the wrapping arm binds moving to and fro the round bale. If the bale is bound, the arm in the middle stops.

Per hand the rope / lever is pulled for the ejection and the bale is ejected.

Look inside

 A: Stop valve

B: throttle for controlling the lowering speed

C: cylinder for lifting the tailgate

Cable for the electrical signal - red on Plus, green to ground

Role binding cord
25x18 cm

Wrapping arm with rope, below the cutter and the contact for the signal

Cutter and the contact for the signal

Release lever with rope for ejection

support wheel

Short hitch for 250 €

directly behind the tractor for easier turns:

Long hitch for 350 € (without PTO shaft), adjustable behind the tractor and beside the tractor:

Stationary hay baling in a barn:

Even the hay from last year can be pressed to save space:

Please shorten the PTO shaft to the appropriate length and fill 46er hydraulic oil in the hydraulic pump!

We guarantee a serious carrying out. You have a full right of return.


Here are some pictures and a video of a satisfied customer about the hay harvest:

We can continue to offer you a special service!

We have a specialist who can give you tips on setting the machine.

Contact us if necessary (this only applies to devices from the company Motorgeräte Fritzsch GmbH)!


The new delivery is here:

Due to the high quality you have 2 years warranty and 1 year additional MGF warranty for private use.
MGF / Motorgeräte Fritzsch Warranty: Includes the free provision of spare parts upon detection of a material defect in the 3rd year, excluded from the MGF warranty are wearing parts, the remuneration of labor and other expenses.


⇒ Typing errors, misapprehensions and changes excepted.

top top

Customers who bought this product also bought the following products:

Hay tedder FM210 with windrowing, rotary tedder for tractors - turn to hay and combine swaths

Hay tedder FM210 with windrowing, rotary tedder for tractors - turn to hay and combine swaths

1.999,00 EUR (19 % VAT incl. * Shipping information)
Parse Time: 0.980s